# Materials Handling Safety Basics

Source: https://usi.how/osha-10-construction/materials-handling-safety-basics

## Manual Materials Handling

### Proper Lifting Technique

- Plan the lift before starting
- Get close to the load
- Maintain a wide base of support (feet shoulder-width apart)
- Bend at knees and hips, not waist
- Tighten core muscles
- Lift with your legs, not your back
- Hold load close to your body
- Avoid twisting while lifting
- Move your feet to turn
 

### Weight Limits

- No single "safe" weight limit for everyone
- Consider your own capabilities and limitations
- Use the 51-pound guideline as a maximum for ideal conditions
- Reduce weight for: 
    - Awkward objects
    - Poor grip
    - Above shoulder or below knee lifting
    - Extended reaches
    - Repetitive lifting
    - Twisting while lifting
 

### Team Lifting

- Use when loads are too bulky or heavy for one person
- Choose workers of similar height and strength
- Designate one person as team leader
- Coordinate movements and communicate clearly
- Lift and lower simultaneously
- Use counting ("1-2-3-lift") to coordinate
 

### Carrying Techniques

- Keep load close to body at waist level
- Maintain good posture
- Look ahead, not down at load
- Take small steps
- Change direction with your feet, not by twisting
- Set load down using same technique as lifting
- Use proper gloves for better grip
 

## Mechanical Materials Handling

### When to Use Mechanical Assistance

- Loads over 50 pounds
- Awkward or bulky items
- Repetitive lifting tasks
- Long carrying distances
- Lifting above shoulder height
- Lifting below knee height
- Limited access or confined spaces
 

### Hand Trucks and Dollies

- Load heaviest items on bottom
- Keep load centered and balanced
- Push rather than pull when possible
- Maintain clear visibility over the load
- Use proper securing methods (straps, bungees)
- Inspect wheels before use
 

### Pallet Jacks

- Check for proper function before use
- Center forks in pallet
- Don't overload (check capacity)
- Pull in traffic areas, push in tight spaces
- Keep hands inside handle area
- Lower forks when parking
- Use wheel chocks on slopes
 

### Forklifts

- Only operated by trained, certified operators
- Never walk under raised loads
- Stay clear of operating area
- Make eye contact with operators
- Follow site-specific pedestrian routes
- Know hand signals for communication with operators
 

### Cranes and Hoists

- Only operated by qualified personnel
- Use proper rigging techniques
- Never walk under suspended loads
- Use tag lines to control loads
- Establish clear communication with operator
- Inspect all equipment before use
 

## Material Storage

### General Stacking Rules

- Place heaviest items on bottom shelves
- Keep stacks straight and aligned
- Limit stack height (usually 4 feet without mechanical stacking)
- Cross-tie where appropriate for stability
- Leave adequate aisle space (minimum 3 feet)
- Keep routes clear for emergency access
 

### Pipe and Lumber Storage

- Stack on level ground
- Use chocks or stakes to prevent rolling
- Remove nails and screws before stacking lumber
- Don't store pipes or lumber near electrical lines
- Distribute weight evenly
- Consider wind conditions for outdoor storage
 

### Brick and Block Storage

- Limit height to 7 feet for manual stacking
- Taper back stacks over 4 feet high
- Place on firm, level surface
- Secure loose blocks
- Remove damaged blocks from stacks
 

### Hazardous Materials

- Store according to SDS requirements
- Maintain proper ventilation
- Provide proper containment for spills
- Keep incompatible materials separated
- Ensure proper labeling
- Store only minimum amounts needed
 

## Loading and Unloading

### Delivery Zones

- Designate specific areas for deliveries
- Keep clear of traffic and pedestrians
- Ensure firm, level ground
- Consider weather protection
- Provide adequate lighting
- Establish safe routes to storage areas
 

### Truck Loading/Unloading

- Set brakes and chock wheels
- Inspect truck bed before entering
- Use dock plates/bridges in good condition
- Ensure forklifts are rated for the loading surface
- Maintain load balance across truck bed
- Secure load before moving truck
 

### Material Handling Equipment Safety

- Inspect all equipment before use
- Don't exceed rated capacities
- Use proper attachments for the task
- Keep loads low when traveling
- Travel at safe speeds
- Use spotters for limited visibility
- Follow designated travel routes
 

## Common Injuries and Prevention

### Back Injuries

- Most common materials handling injury
- Often result from improper lifting
- Can cause long-term disability
- Prevent through: 
    - Proper lifting technique
    - Using mechanical aids
    - Planning lifts
    - Stretching before heavy work
 

### Hand and Finger Injuries

- Crushing between materials
- Cuts from sharp edges
- Prevent through: 
    - Proper gloves
    - Hand placement awareness
    - Using hand tools rather than hands
    - Coordinating with coworkers
 

### Foot Injuries

- Dropped materials
- Rolling objects
- Prevent through: 
    - Safety-toe footwear
    - Clear communication during team lifts
    - Proper storage techniques
    - Awareness of surroundings
 

### Strains and Sprains

- Result from overexertion
- Often affect shoulders, knees, wrists
- Prevent through: 
    - Warming up before heavy work
    - Task rotation
    - Using mechanical aids
    - Taking breaks between heavy lifts
 

## Worker Rights and Responsibilities

### Employer Responsibilities

- Provide proper equipment for material handling
- Train workers on safe handling techniques
- Assess workplace for material handling hazards
- Implement controls to reduce manual handling
- Provide appropriate PPE
- Investigate material handling incidents
 

### Worker Responsibilities

- Follow proper lifting procedures
- Use equipment provided
- Ask for help when needed
- Report hazardous conditions
- Participate in training
- Suggest improvements to material handling procedures
