# Working Safely at Heights

Source: https://usi.how/osha-10-construction/working-safely-at-heights

## Planning for Working at Heights

### Risk Assessment

Before starting any work at height:

- Identify all fall hazards
- Evaluate the risks
- Determine appropriate controls
- Document your plan
- Share with all workers
 

### Hierarchy of Fall Protection

Address fall hazards in this order:

1. **Eliminate** the hazard (work from ground level)
2. **Passive protection** (guardrails, barriers)
3. **Fall restraint** (prevents reaching the edge)
4. **Fall arrest** (stops a fall in progress)
5. **Administrative controls** (warning lines, monitors)
 

### Weather Considerations

- Check forecasts before starting
- Postpone work in high winds or storms
- Take precautions for wet or icy conditions
- Consider heat stress in hot weather
- Allow for more breaks in extreme conditions
 

## Types of Fall Protection Systems

### Guardrail Systems

- Top rail 42 inches (±3 inches) high
- Midrail halfway between top rail and working surface
- Toeboard at least 3.5 inches high
- Must withstand 200 pounds of force
- No openings larger than 19 inches
 

### Safety Net Systems

- Installed as close as possible to work area
- No more than 30 feet below working level
- Extend 8-13 feet beyond edge of work surface
- Inspected weekly at minimum
- Tested after initial installation
 

### Personal Fall Arrest Systems

- Full-body harness
- Connecting device (lanyard, lifeline, deceleration device)
- Secure anchor point (5,000 pounds per worker)
- Free fall limited to 6 feet
- Must prevent contact with lower level
 

### Fall Restraint Systems

- Similar components to fall arrest systems
- Designed to prevent reaching fall hazard
- Must adjust length to keep worker from reaching edge
- Requires less fall clearance than arrest systems
 

### Positioning Device Systems

- Allows hands-free work on vertical surfaces
- Limits free fall to 2 feet
- Often used for rebar work, form work, etc.
- Not a substitute for fall arrest when needed
 

## Safe Work Areas at Heights

### Controlled Access Zones

- Designated areas where certain work can be done without conventional fall protection
- Marked by control lines
- Access limited to authorized workers
- Warning lines clearly visible
- Requires safety monitor
 

### Warning Line Systems

- Physical barriers marking safe work zones
- Set 6-15 feet back from edge (depending on work)
- Lines flagged every 6 feet
- Set 34-39 inches above surface
- Clearly visible to workers
 

### Safety Monitoring Systems

- Designated safety monitor watches workers
- Monitor has no other duties
- Must be on same walking/working surface
- Must be close enough for verbal communication
- Only used when no other protection is feasible
 

## Safe Access to Heights

### Ladders

- Extend 3 feet above landing surface
- Secured at top and bottom
- Placed at proper angle (4:1 ratio)
- Used on stable, level ground
- Inspected before each use
 

### Scaffolds

- Fully planked with proper decking
- Guardrails when 10+ feet high
- Proper access built in
- Inspected by competent person
- Properly braced and tied to structure
 

### Lifts and Platforms

- Only operated by trained personnel
- Maintained according to manufacturer specs
- Never moved with elevated workers
- Outriggers deployed when required
- Fall protection still used as needed
 

### Stairs and Ramps

- Handrails on all stairs with 4+ risers
- Minimum width of 22 inches
- Uniform riser height and tread depth
- Non-slip surfaces
- Proper lighting
 

## Hole and Opening Protection

### Floor Holes

- Covered with material that supports 2x expected load
- Secured to prevent displacement
- Marked with "HOLE" or "COVER"
- Guardrails installed if cover isn't feasible
 

### Wall Openings

- Protected if drop is 6+ feet and opening is 18+ inches
- Guardrail, screen, or mesh required
- Fall arrest system if other protection not feasible
 

### Skylights

- Treated as holes in walking surface
- Never sat or stepped on
- Protected by covers, screens, or guardrails
- Warning signs not sufficient protection
 

## Safe Work Practices

### Equipment Inspection

Before each use, inspect all fall protection equipment for:

- Cuts, tears, abrasions
- Stretching or deformation
- Rust or corrosion
- Missing parts or tags
- Impact indicators
- Proper function of moving parts
 

### Proper Use Techniques

- Never tie knots in lanyards (weakens them)
- Don't wrap lanyards around sharp edges
- Connect snap hooks only to compatible connectors
- Don't connect multiple lanyards together
- Stay directly under anchor points when possible
- Remove damaged equipment from service
 

### Housekeeping

- Keep work areas clean and organized
- Immediately clean up spills
- Store tools and materials away from edges
- Secure tools to prevent drops
- Mark and barricade dangerous areas
 

## Fall Protection for Specific Tasks

### Roofing Work

- Different requirements for low-slope vs. steep roofs
- Warning lines with safety monitors in some cases
- Slide guards on steep roofs in limited circumstances
- See roof-specific guidelines
 

### Steel Erection

- Fall protection at 15+ feet in most cases
- Specialized connectors' rules apply
- Controlled decking zones have specific requirements
- Perimeter safety cables or guardrails required
 

### Residential Construction

- Conventional fall protection required at 6+ feet
- Alternative methods only with written plan
- Slide guards not sufficient alone on steep roofs
- Proper training required for each method used
 

## Emergency Response

### Rescue Planning

- Must have plan for prompt rescue
- Self-rescue options identified
- Assisted rescue methods established
- Proper equipment available
- Regular practice of rescue procedures
 

### Suspension Trauma

- Can occur within minutes of suspension in harness
- Can lead to serious injury or death
- Prevention includes trauma straps on harnesses
- Movement of legs if suspended
- Rapid rescue is essential
